D7745 Standard Practice for Testing Pultruded Composites has been revised to D7745-19

» Código: ASTM D7745 - 19

» Comité: Subcommittee: D20.18

» Más información

Solicitar Norma

Significance and Use

4.1 This practice is intended to aid in the selection of test protocols for reinforced pultruded composites.

4.2 This practice is intended to define the locations from which test specimens shall be taken from the reinforced pultruded composite.

1. Scope

1.1 This protocol summarizes the applicable ASTM and other standard test methods commonly used for pultruded composites. The individual performance requirements to these test methods are defined by specific customer specifications.

1.2 This protocol also defines appropriate specimen locations for sampling from the pultruded composites.

1.3 This protocol does not discuss all possible standard test methods that may be utilized for pultruded composites.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 1: There is no known ISO equivalent to this guide.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies

D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics

D495 Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation

D570 Test Method for Water Absorption of Plastics

D635 Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position

D638 Test Method for Tensile Properties of Plastics

D695 Test Method for Compressive Properties of Rigid Plastics

D696 Test Method for Coefficient of Linear Thermal Expansion of Plastics Between 30C and 30C with a Vitreous Silica Dilatometer

D732 Test Method for Shear Strength of Plastics by Punch Tool

D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement

D883 Terminology Relating to Plastics

D953 Test Method for Pin-Bearing Strength of Plastics

D2291 Practice for Fabrication of Ring Test Specimens for Glass-Resin Composites

D2343 Test Method for Tensile Properties of Glass Fiber Strands, Yarns, and Rovings Used in Reinforced Plastics

D2344/D2344M Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates

D2583 Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor

D2584 Test Method for Ignition Loss of Cured Reinforced Resins

D2734 Test Methods for Void Content of Reinforced Plastics

D3039/D3039M Test Method for Tensile Properties of Polymer Matrix Composite Materials

D3647 Practice for Classifying Reinforced Plastic Pultruded Shapes According to Composition

D3846 Test Method for In-Plane Shear Strength of Reinforced Plastics

D3914 Test Method for In-Plane Shear Strength of Pultruded Glass-Reinforced Plastic Rod

D3916 Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced Plastic Rod

D3917 Specification for Dimensional Tolerance of Thermosetting Glass-Reinforced Plastic Pultruded Shapes

D4065 Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures

D4385 Practice for Classifying Visual Defects in Thermosetting Reinforced Plastic Pultruded Products

D4475 Test Method for Apparent Horizontal Shear Strength of Pultruded Reinforced Plastic Rods By the Short-Beam Method

D4476 Test Method for Flexural Properties of Fiber Reinforced Pultruded Plastic Rods

D5028 Test Method for Curing Properties of Pultrusion Resins by Thermal Analysis

D5117 Test Method for Dye Penetration of Solid Fiberglass Reinforced Pultruded Stock

D5379/D5379M Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method

D5420 Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)

D6641/D6641M Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture

D7029 Test Method for Determination of Reactivity of Unsaturated Polyesters and Vinyl Esters at 180.0F (82.2C)

D7136/D7136M Test Method for Measuring the Damage Resistance of a Fiber-Reinforced Polymer Matrix Composite to a Drop-Weight Impact Event

D7290 Practice for Evaluating Material Property Characteristic Values for Polymeric Composites for Civil Engineering Structural Applications

D7332/D7332M Test Method for Measuring the Fastener Pull-Through Resistance of a Fiber-Reinforced Polymer Matrix Composite

D7792 Practice for Freeze/Thaw Conditioning of Pultruded Fiber Reinforced Polymer (FRP) Composites Used in Structural Designs

D7992 Practice for Elevated Temperature and Moisture Conditioning of Pultruded Fiber Reinforced Polymer (FRP) Composites Used in Structural Designs

D8019 Test Methods for Determining the Full Section Flexural Modulus and Bending Strength of Fiber Reinforced Polymer Crossarms Assembled with Center Mount Brackets

D8069 Test Method for Determining Flexural Modulus of Full Section Pultruded Fiber Reinforced Polymer (FRP) Composite Members with Doubly Symmetric Cross Sections under Bending

E84 Test Method for Surface Burning Characteristics of Building Materials

E662 Test Method for Specific Optical Density of Smoke Generated by Solid Materials

E1922 Test Method for Translaminar Fracture Toughness of Laminated and Pultruded Polymer Matrix Composite Materials

F1092 Specification for Fiberglass (GRP) Pultruded Open-Weather Storm and Guard, Square Railing Systems

G154 Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials

RECOMENDAR
Su nombre:
Correo-e destinatario:
*Para varios destinatarios, utilice la coma como separador
Comentarios:
Delicious Menéame
Yahoo
Buzz!

Financiado por: