D5963 Standard Test Method for Rubber Property#x2014;Abrasion Resistance (Rotary Drum Abrader) has been reapproved, available as D5963-04(2019)

» Código: ASTM D5963 - 04(2019)

» Comité: Subcommittee: D11.15

» Más información

Solicitar Norma

Significance and Use

5.1 Abrasion resistance is a performance factor of paramount importance for many rubber products, such as tires, conveyor belts, power transmission belts, hoses, footwear, and floor covering. A test capable of measuring resistance to abrasion of rubber, including uniformity of wear behavior under abrasive/frictional service conditions is therefore highly desirable.

5.2 This test method may be used to estimate the relative abrasion resistance of different rubbers. Since conditions of abrasive wear in service are complex and vary widely, no direct correlation between this accelerated test and actual performance can be assumed.

5.3 This test method is suitable for comparative testing, quality control, specification compliance testing, referee purposes, and research and development work.

1. Scope

1.1 This test method covers the measurement of abrasion resistance of rubbers (vulcanized thermoset rubbers and thermoplastic elastomers) that are subject to abrasive/frictional wear in actual service. The abrasion resistance is measured by moving a test piece across the surface of an abrasive sheet mounted to a revolving drum, and is expressed as volume loss in cubic millimetres or abrasion resistance index in percent. For volume loss, a smaller number indicates better abrasion resistance, while for the abrasion resistance index, a smaller number denotes poorer abrasion resistance.

1.2 Test results obtained by this test method shall not be assumed to represent the wear behavior of rubber products experienced in actual service.

1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D297 Test Methods for Rubber ProductsChemical Analysis

D1765 Classification System for Carbon Blacks Used in Rubber Products

D2240 Test Method for Rubber PropertyDurometer Hardness

D3182 Practice for RubberMaterials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets

D4483Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries

Other Standards

DIN 53516 Determination of Abrasion Resistance Available from Beuth Verlag GmbH (DIN-- DIN Deutsches Institut fur Normung e.V.), Burggrafenstrasse 6, 10787, Berlin, Germany.

ISO 2393 Rubber Test MixesPreparation, Mixing and VulcanizationEquipment and Procedures

ISO 2781 Rubber, VulcanizedDetermination of Density

ISO 4649 RubberDetermination of Abrasion Resistance Using a Rotating Cylindrical Drum Device

ISO 5725 Precision of Test MethodsDetermination of Repeatability and Reproducibility for a Standard Test Method by Interlaboratory Tests

ISO 7619 RubberDetermination of Indentation Hardness by Means of Pocket Hardness Meters

ISO 9298 Rubber Compounding IngredientsZone Oxide Test Methods

RECOMENDAR
Su nombre:
Correo-e destinatario:
*Para varios destinatarios, utilice la coma como separador
Comentarios:
Delicious Menéame
Yahoo
Buzz!

Financiado por: